PPE Knowledge Centre

Safety Shoes — Lighter Duty Footwear

A practical Jaybee Supplies guide to safety shoes, lightweight safety trainers, occupational footwear, EN ISO 20345, EN ISO 20346, EN ISO 20347, slip resistance, ESD protection, anti-fatigue comfort and correct footwear selection.

Guide Type

Knowledge Centre

Topic

Safety Shoes

Audience

Workers & Buyers

Focus

Slip, Toe & ESD Risk

Need help choosing?

Jaybee Supplies can help you compare safety trainers, lightweight safety shoes, ESD shoes, anti-fatigue footwear, slip-resistant shoes, food service footwear and occupational footwear.

01282 505043

sales@jaybeesupplies.co.uk

1. Foot Protection Risk

Safety Shoes Overview

Safety shoes are a lighter-weight, lower-profile category of protective footwear. They are designed for workplaces where full-height safety boots may be impractical, uncomfortable or over-specified, but where foot protection is still required.

Safety shoes can protect against hazards such as falling goods, toe impact, slips, sharp debris, wet floors, electrostatic discharge and fatigue from prolonged standing. The correct product depends on the task, workplace surface, slip risk, toe protection requirement, midsole requirement, fit and wearer comfort.

Key point: safety shoes can be covered by the same EN ISO 20345 safety footwear standard as safety boots. The low-cut style does not make them “less official”, but it may make them unsuitable for work where ankle support or rough outdoor protection is needed.

Safety Shoes vs Safety Boots

Factor Safety Shoe Safety Boot
Ankle Support Low-cut design with limited ankle support. Higher ankle support for rougher environments.
Indoor / Smooth Floors Often preferred because they are lighter and more comfortable. Can be over-specified for low-risk indoor roles.
Construction Sites Generally not appropriate for many sites where S3 boots are required. Preferred for most construction and outdoor work.
Retail / Office-Adjacent Roles More suitable for customer-facing and office-adjacent work. May appear excessive in lighter-duty environments.
Prolonged Standing Lower weight and good insoles can improve comfort. Heavier footwear may increase fatigue if not needed for the risk.

3. Standards

Safety Shoe Standards and Suffix Codes

Safety shoes, protective shoes and occupational shoes are not the same thing. The standard tells you whether the footwear includes a rated toe cap and what type of protection it is designed to provide.

Standard Category Toe Cap Key Use
EN ISO 20345 S1–S5 / SB 200J impact, 15kN compression Safety footwear, including occupational safety shoes.
EN ISO 20346 P1–P5 / PB 100J impact, 10kN compression Protective footwear for lower-risk impact hazards.
EN ISO 20347 O1–O5 / OB No protective toe cap Occupational footwear for slip resistance, hygiene or comfort where toe protection is not required.

EN ISO 20345 Suffix Codes for Safety Shoes

Code Meaning Typical Use
S1 200J toe cap, antistatic protection and energy-absorbing heel. Indoor light industry and warehousing.
S1P S1 plus penetration-resistant midsole. Occasional nail, staple or sharp debris risk.
S2 S1 plus water-resistant upper. Light outdoor use, food service and wet floor environments.
S3 S2 plus penetration midsole and cleated sole. Where S3 protection is required but a low-cut shoe is preferred over a boot.
SRC Slip tested on ceramic tile and steel surfaces. Healthcare, food, retail and wet or smooth floors.
ESD Electrostatic discharge rated. Electronics, cleanrooms and pharmaceutical environments.
CI Cold insulation. Chill rooms and cool environments.

Important: EN ISO 20347 footwear does not include a toe cap. If toe impact or compression risk is identified, EN ISO 20345 or EN ISO 20346 footwear should be selected instead.

4. Footwear Types

Types of Safety Shoe

Safety shoes are available in several designs for different environments. The right type depends on the surface, standing time, wearer role, toe hazard, hygiene needs and any special requirements such as ESD control.

Type Typical Standard Primary Use
Safety Trainer EN ISO 20345 S1–S3 Warehousing, light manufacturing and logistics.
Court / Oxford Style Safety Shoe EN ISO 20345 S1–S2 Office-adjacent, retail and customer-facing roles.
Safety Clog EN ISO 20347 O2 SRC Healthcare, food service and catering where toe protection is not required.
ESD Safety Shoe EN ISO 20345 ESD Electronics manufacturing, cleanrooms and pharmaceutical environments.
Anti-Fatigue Safety Shoe EN ISO 20345 S1/S2 with suitable insole support Prolonged standing in warehouses, checkouts and food preparation areas.
Waterproof Membrane Safety Shoe EN ISO 20345 S2/S3 Light outdoor use, food service, car parks and wet areas.
Cold Store Safety Shoe EN ISO 20345 S1/S2 CI Chill rooms around 0–10°C for short-duration entry.

5. Applications

Industry Applications

Safety shoes are commonly used in lighter-duty and indoor workplaces where toe protection, slip resistance, comfort or static control is needed without the height and weight of a full safety boot.

Industry / Role Primary Hazards Recommended Safety Shoe
Warehousing / Picking Falling goods, trolleys and hard concrete floors. EN ISO 20345 S1P SRC safety trainer.
Retail Customer-Facing Roles Light dropped goods and hard floors. EN ISO 20345 S1 SRC court-style safety shoe.
Food Service / Catering Wet floors and dropped equipment. EN ISO 20347 O2 SRC or EN ISO 20345 S2 SRC where toe protection is required.
Healthcare Slip-resistant hard floors and hygiene requirements. EN ISO 20347 O2 SRC safety clog or shoe where no toe cap is required.
Electronics Manufacturing Static discharge to components. EN ISO 20345 ESD-rated safety shoe.
Pharmaceutical Production Clean environments, static control and slip risk. EN ISO 20345 ESD S1 SRC cleanroom-compatible footwear.
Office / Site-Adjacent Admin Occasional site visits and low-level toe hazards. EN ISO 20345 S1 SRC safety shoe or lightweight trainer.
Light Assembly / Manufacturing Dropped components and hard floors. EN ISO 20345 S1P SRC with anti-fatigue insole.
Education Workshops / DT Dropped tools and workshop debris. EN ISO 20345 S1P SRC safety trainer.

Jaybee Supplies Can Help Source Safety Footwear

From lightweight safety trainers and customer-facing safety shoes to ESD footwear, slip-resistant clogs, anti-fatigue shoes and wider PPE, Jaybee Supplies can help your team choose footwear that matches the workplace risk.

Shop PPE Equipment

6. Selection

How to Select the Right Safety Shoes

Safety shoes are often selected on appearance, especially in retail, healthcare, logistics and office-adjacent roles. Appearance matters for wearer acceptance, but it should never come before the required protection code.

Selection principle: identify the hazard first, then confirm toe protection, midsole protection, slip resistance, water resistance, ESD needs, comfort, fit and suitability for the working surface.

Selection Checks

  • Indoor, dry, flat floors: S1 SRC footwear may be suitable where toe protection, antistatic properties, heel energy absorption and slip resistance are required.
  • Indoor work with sharp debris: S1P SRC adds penetration-resistant midsole protection.
  • Light outdoor or wet indoor work: S2 SRC adds a water-resistant upper.
  • Static-sensitive environments: ESD S1 or S1P SRC footwear may be required.
  • Food service and wet floors: S2 SRC or EN ISO 20347 O2 SRC may be suitable depending on toe impact risk.
  • Healthcare with no impact hazard: EN ISO 20347 O2 SRC may be appropriate only where risk assessment confirms no toe cap is needed.
  • Construction sites: low-cut safety trainers may be unsuitable where S3 safety boots are required.

Fit for Long-Duration Wear

  • Fit later in the day: feet can swell during a shift, so end-of-day fitting gives a more realistic result.
  • Allow toe room: allow around 10–12mm at the toe while ensuring the heel remains secure.
  • Fit the larger foot: many people have one foot slightly larger than the other.
  • Check width: multiple width fittings may be needed because wrong-width shoes cause fatigue and blisters.
  • Use anti-fatigue insoles: workers standing on hard floors all day may need better cushioning and support.

Questions Before Buying

  • Is toe protection required? If yes, EN ISO 20345 or EN ISO 20346 should be considered.
  • Is there a penetration risk? If yes, S1P or S3 footwear may be required.
  • Are floors wet, greasy or smooth? Slip resistance should be a priority.
  • Is ESD protection required? If yes, footwear must be part of a complete ESD control system.
  • Will the wearer stand all day? Lightweight shoes and anti-fatigue insoles may improve comfort and compliance.

7. Fit & Maintenance

Fit, Use and Maintenance

Safety shoes only protect properly when they fit, fasten and grip correctly. Poor fit can create fatigue, blisters, trips and lower-limb discomfort, while worn soles and compacted insoles can reduce protection and comfort.

Correct Use

  • Fasten fully: laces, straps or closures should be secured because loose shoes can become a trip hazard.
  • Do not share safety shoes: fit, hygiene and infection risk make shared footwear unsuitable.
  • Use the correct socks: socks can affect comfort, moisture control and ESD performance.
  • Do not modify footwear: drilling, cutting, stretching or unauthorised alterations can affect protection.
  • Use the footwear for the intended task: safety trainers should not be used where boots are required.

Maintenance

  • Replace insoles regularly: compacted insoles no longer provide anti-fatigue support.
  • Clean sole tread: dirt, grease and food debris in the tread can reduce slip resistance.
  • Dry at room temperature: direct heat can warp soles, damage uppers and reduce comfort.
  • Check ESD performance: ESD shoes rely on the complete chain of shoe, sock, wearer and floor.
  • Keep footwear clean: contaminated uppers and soles can affect hygiene and safety.

8. Inspection

Inspection and Replacement

Safety shoes should be inspected regularly and replaced when soles are worn, toe protection is damaged, uppers split, ESD resistance is lost or comfort support has broken down. A shoe may look acceptable from above while the sole or inner structure is no longer safe.

Inspection Point What to Check Action
Sole Tread Smooth, worn, clogged or damaged tread. Replace if slip resistance is compromised.
Toe Area Cracking, deformation, impact damage or exposed toe cap. Replace if toe cap integrity is uncertain.
Upper Cracks, splits, delamination, water ingress or damage at the welt and heel. Replace if protection or hygiene is affected.
Laces and Fastenings Worn laces, damaged eyelets, broken straps or failed fasteners. Repair or replace before use.
Heel Counter Collapsed or soft heel support. Replace if support is lost.
ESD Protection Discharge path and resistance reading where ESD footwear is required. Test with suitable ESD equipment and replace if out of specification.
Insoles Compression, heavy soiling, odour, damage or loss of support. Replace insoles or footwear as needed.

Replacement Triggers

  • Sole tread worn smooth: replace because slip resistance is compromised.
  • Toe cap area cracked or deformed: replace because toe cap integrity is uncertain.
  • Upper cracked or delaminating: replace because water resistance and structure may be lost.
  • ESD resistance out of specification: replace because electrostatic discharge protection is lost.
  • Heavy use: assess around 12 months and replace if wear is visible.
  • Light use: assess around 24 months and replace if protection or comfort is reduced.

9. Common Mistakes

Common Safety Shoe Mistakes

Common Mistake Why It Matters / Correct Practice
Selecting safety shoes by appearance A stylish shoe without the required code is not compliant PPE. Selection must be hazard-led.
Using EN ISO 20347 where a toe cap is required EN ISO 20347 has no toe cap. Where toe impact risk exists, EN ISO 20345 or EN ISO 20346 is required.
Not replacing worn soles A worn sole can provide poor slip resistance, especially on wet food, healthcare or polished floors.
Using ESD shoes without checking the discharge path ESD protection depends on shoe, sock, wearer and floor. Any break in that chain can defeat protection.
Not fitting safety shoes individually Shoes that are too small cause blisters and fatigue. Shoes that are too large create trip risk.
Using safety trainers on construction sites Many construction sites require S3 safety boots. Trainers may lack cleated sole, waterproofing, ankle support or midsole protection.
Not replacing insoles Compacted insoles can increase lower limb and back fatigue for workers standing on hard floors all day.

10. Resources

Training and Further Resources

Workers should understand why safety shoes are required, how to check the markings, how to keep footwear clean, when to report wear and why different environments require different footwear codes.

Always check official guidance directly before making compliance decisions.

Internal Resources to Add

  • Footwear risk assessment template.
  • Safety footwear issue record.
  • Slip risk assessment and floor cleaning guidance.
  • ESD footwear testing schedule where relevant.
  • Footwear replacement and inspection policy.
  • Approved footwear list by department or role.

Document Review Log

Use this space internally to record future content reviews, compliance checks or product updates.

Version Date Reviewed By Changes Made
1.0 May 2026 Jaybee Supplies Initial Knowledge Centre page created.

Need Safety Shoes for Your Team?

Jaybee Supplies can help you choose safety trainers, lightweight safety shoes, slip-resistant footwear, ESD shoes, anti-fatigue footwear, food service shoes and wider PPE for your workplace.

Call 01282 505043

sales@jaybeesupplies.co.uk

Smart Online Portal