PPE Knowledge Centre

Welding PPE

A practical Jaybee Supplies guide to welding helmets, shade numbers, flame-resistant clothing, welding gloves, safety boots, respiratory protection, hearing protection and full PPE selection for welding and allied processes.

Guide Type

Knowledge Centre

Topic

Welding PPE

Audience

Workers & Buyers

Focus

Arc, Fume & Heat Risk

Need help choosing?

Jaybee Supplies can help you compare welding helmets, welding gauntlets, flame-resistant clothing, safety boots, RPE, hearing protection and wider workplace PPE.

01282 505043

sales@jaybeesupplies.co.uk

1. Welding Risk

Welding PPE Overview

Welding and allied processes create several hazards at the same time. Welders may be exposed to arc flash, ultraviolet radiation, infrared radiation, welding fume, heat, molten metal spatter, noise, grinding debris and hot workpieces during a single task.

No single item of PPE protects against every welding hazard. A complete welding PPE ensemble should be selected for the process, material, current, work position, ventilation, fume controls and surrounding activity.

Key point: welding PPE should protect the eyes, face, skin, hands, feet, lungs and hearing. The right helmet without RPE, or the right jacket with synthetic base layers, can still leave serious exposure gaps.

Main Welding Hazards

Hazard Source PPE Required
Arc Flash / UV / IR Radiation The welding arc across all arc processes. Welding helmet with correct shade filter.
Welding Fume Arc welding processes, especially MMA, MIG and MAG. RPE, usually FFP3 minimum or TH3 PAPR for regular work.
Molten Metal Spatter MMA, MIG/MAG, cutting and gouging. FR clothing, welding gloves and suitable face protection.
Contact Heat Hot workpieces, spatter and equipment. Welding gauntlets, FR clothing and safety boots.
UV Skin Exposure Arc radiation from welding. FR clothing covering all skin and suitable neck protection.
Noise Grinding, chipping, plasma cutting and fabrication tasks. Ear defenders where required by noise assessment.
Foot Injury Spatter, dropped materials and hot metal. Safety boots with heat-resistant outsole where required.

3. Eye & Face Protection

Welding Helmet and Eye Protection

Welding helmets and filters protect against intense visible light, ultraviolet radiation, infrared radiation and spatter. The correct filter shade depends on the welding process and current. Auto-darkening filters should be checked before every welding session.

Welding Helmet Standards

  • EN 175: welding helmets and hand shields for arc welding.
  • EN 169: passive welding filter shade numbers.
  • EN 379: auto-darkening welding filters that electronically darken when the arc is struck.
  • EN 166: safety goggles and face shields used for grinding, chipping and related eye hazards.

Important: inspect the filter before use. A cracked or damaged welding filter provides no reliable arc protection. Auto-darkening helmets should be tested before every welding session.

Grinding After Welding

When the welding helmet is raised for grinding, chipping or dressing welds, the eye hazard changes. Workers should use suitable safety goggles and face protection for flying particles and fragments.

4. Shade Guide

Welding Shade Number Guide

The correct shade protects against optical radiation while allowing the welder to see the work. The required shade depends on process and current. Always check manufacturer guidance and risk assessment for the task.

Process Current / Tip Size Typical Shade
MMA / Stick Up to 100A Shade 10
MMA / Stick 100–200A Shade 11
MMA / Stick 200–300A Shade 12
MMA / Stick 300A+ Shade 13–14
MIG / MAG Up to 250A Shade 11
MIG / MAG 250A+ Shade 12–13
TIG Up to 100A Shade 9–10
TIG 100–200A Shade 10–11
Plasma Cutting Up to 80A Shade 9
Gas Welding Light tip Shade 4–5
Gas Welding Heavy tip Shade 6–7

5. Full Ensemble

Complete Welding PPE Ensemble

Welding PPE should be treated as a complete system. Each part protects a different body area and should be compatible with the welding process, environment and other PPE being worn.

Body Area PPE Item Standard / Requirement
Head and Face Welding helmet, passive or auto-darkening. EN 175 with EN 169 or EN 379 filter.
Eyes During Grinding Safety goggles and face shield when helmet is raised. EN 166.
Body / Torso FR welding jacket or coverall. EN ISO 11611 Class 2 for MMA/MIG; Class 1 for lower-risk TIG or brazing where suitable.
Under-Layers FR base layers if worn. Avoid polyester and nylon because synthetic layers can melt.
Hands Welding gauntlets. EN ISO 12477; heavy gloves for MMA/MIG and thinner gloves for TIG dexterity.
Feet Safety boots with heat-resistant outsole. EN ISO 20345 S3 HRO where required. Boot tops should be covered by welding trousers.
Respiratory RPE for welding fume. FFP3 minimum for short-duration work or EN 12941 TH3 PAPR for regular welding where suitable.
Hearing Ear defenders or ear plugs. EN 352-1 or EN 352-2 based on noise assessment.
Neck Neck flap or FR balaclava. Helps prevent UV arc burn, especially during overhead welding.

Important: welding fume, including mild steel welding fume, requires proper control. General ventilation alone should not be assumed to protect the breathing zone. LEV, suitable RPE and correct working methods should be considered together.

6. Welding Fume

RPE for Welding Fume

Respiratory protection for welding should be selected through COSHH assessment. The material, coating, welding process, duration, work position, ventilation and exposure level all affect the level of respiratory protection needed.

HSE: Welding fume — RPE and LEV requirements

Welding Scenario Typical RPE Consideration
Short-Duration Mild Steel Welding With LEV FFP3 disposable respirator may be the minimum where assessment confirms suitability.
Regular Welding or Insufficient LEV Powered air respiratory protection, such as TH3 PAPR, may be required.
Stainless, Galvanised or Coated Metals Higher-risk fumes may require TH3 PAPR or other enhanced controls.
Confined Space Welding Airline respirator or SCBA may be required. Filtering RPE is not suitable for oxygen-deficient or unknown atmospheres.

Selection reminder: RPE is not a substitute for controlling fume at source. Use local exhaust ventilation and suitable respiratory protection where required.

Jaybee Supplies Can Help Source Welding PPE

From welding helmets and auto-darkening filters to welding gauntlets, FR clothing, safety boots, RPE and hearing protection, Jaybee Supplies can help your team choose suitable PPE for welding and fabrication work.

Shop PPE Equipment

7. Fit & Maintenance

Fit, Use and Maintenance

Welding PPE only protects when worn properly and kept in good condition. Gaps in clothing, raised helmets, damaged filters, wrong glove choice, exposed boot tops or non-FR base layers can all lead to serious injury.

Clothing and Fit

  • Fasten fully: FR jacket and coverall fastenings should be closed before striking the arc.
  • Do not roll sleeves up: exposed arms are vulnerable to arc burn and spatter.
  • Cover boot tops: welding trousers should sit over boot tops so spatter cannot fall inside.
  • Use FR underlayers: clothing worn under welding jackets should not be polyester, nylon or other melt-risk synthetics.
  • Protect the neck: use a neck flap or FR balaclava where arc exposure can reach the neck.

Helmet Use

  • Inspect the filter: cracked, damaged or arc-marked filters should be replaced before welding.
  • Lower before striking: the helmet should be in place before the arc is struck.
  • Test auto-darkening helmets: check the darkening function, sensor cleanliness and battery before every session.
  • Switch protection for grinding: use goggles and face protection when the welding helmet is raised for grinding or chipping.

Gloves, Boots and RPE

  • Choose glove type by process: heavier gauntlets suit MMA/MIG, while TIG usually needs thinner gloves for dexterity.
  • Check boots: boot tops should be covered and heat-resistant soles should be specified where hot surfaces or spatter are present.
  • Check RPE before use: filters, batteries, airflow and face seals should be confirmed before welding begins.
  • Keep PPE dry and clean: contaminated or wet PPE can lose performance and increase comfort issues.

8. Inspection

Inspection and Replacement

Welding PPE should be inspected before use and replaced where protection is reduced. Burn-through, holes, cracked filters, failed auto-darkening cartridges and damaged gloves can expose the wearer immediately.

Inspection Point What to Check Action
Welding Helmet Filter Cracks, arc damage, loose filter or poor visibility. Replace before welding if damaged.
Auto-Darkening Helmet Darkening function, sensor cleanliness and battery level. Do not weld if the cartridge fails to work correctly.
Welding Jacket / Coverall Burn-through, thinning, holes, missing stitching or damaged closures. Replace if thermal protection is lost.
Welding Gloves Burn holes, thinning at fingertips, split seams or palm damage. Replace if heat or spatter can reach skin.
Safety Boots HRO sole condition, toe cap damage and spatter damage around boot tops. Replace if protection is damaged or uncertain.
RPE Facepiece, valves, filters, battery, airflow and filter schedule. Do not use if defective or out of service life.
FR Clothing System Confirm outerwear and underlayers are suitable for welding. Remove non-FR or melt-risk layers before work.

Replacement Triggers

  • Cracked welding filter: replace immediately because arc protection is no longer reliable.
  • Auto-darkening function failure: replace before welding because arc eye risk is immediate.
  • Jacket burn-through: replace because heat and UV protection are lost at the damaged area.
  • Burn holes in gloves: replace because spatter can reach the skin.
  • Non-FR base layer: replace with suitable FR clothing before welding continues.
  • Damaged RPE or expired filters: replace before entering the welding fume area.

9. Common Mistakes

Common Welding PPE Mistakes

Common Mistake Why It Matters / Correct Practice
Not testing auto-darkening helmet before welding A failed cartridge gives no reliable arc protection. Test before every session.
Wearing non-FR clothing under a welding jacket Synthetic base layers can melt in heat or arc flash and cause severe burns.
Using FFP2 or a basic dust mask for welding fume Welding fume requires suitable respiratory protection selected through assessment. FFP3 is commonly the minimum for many welding tasks.
Raising the helmet for grinding without eye protection Grinding debris can cause serious eye injuries. Use suitable goggles and face protection.
Using thick MMA/MIG gauntlets for TIG welding Poor dexterity can encourage unsafe glove removal. Use TIG-specific gloves where suitable.
Relying on general workshop ventilation General ventilation may not control fume at the breathing zone. LEV and RPE may be required.
Leaving boot tops uncovered Spatter inside a boot can cause serious burns. Welding trousers should cover boot tops.

10. Resources

Training and Further Resources

Workers carrying out welding or allied processes should understand the hazards from the arc, fume, heat, spatter, grinding and noise. Training should cover PPE selection, correct wearing, filter shade choice, RPE use, fume control and inspection before work starts.

Always check official guidance directly before making compliance decisions.

Internal Resources to Add

  • Welding risk assessment template.
  • COSHH assessment for welding fume.
  • LEV inspection and maintenance records.
  • RPE fit testing records and filter change schedule.
  • Welding PPE issue and inspection record.
  • Hot work permit and fire watch procedure.
  • Approved welding PPE list by process and material.

Document Review Log

Use this space internally to record future content reviews, compliance checks or product updates.

Version Date Reviewed By Changes Made
1.0 May 2026 Jaybee Supplies Initial Knowledge Centre page created.

Need Welding PPE for Your Team?

Jaybee Supplies can help you choose welding helmets, auto-darkening filters, welding gauntlets, FR clothing, safety boots, RPE, hearing protection and wider PPE for fabrication and hot work environments.

Call 01282 505043

sales@jaybeesupplies.co.uk

Smart Online Portal